Origami Swan (medium)

By Dallin -
The swan is a very elegant bird, and this origami model is no exception. It is quite a bit harder than the other swan I have on this blog, and I do not go over the reverse folds in detail. It is best when made out of white paper, but I used yellow to help distinguish each side better.



Step 1: Fold a kite base and turn it over so that the flaps are on the back


Step 2: Valley fold the far left point in


Step 3: Valley fold that same point to the far left edge


Step 4: Continue folding the point out so the crease you made in step 3 lines up with the left edge


Step 5: Valley fold the model in half


Step 6: Take the far left point and bring it down a little to adjust the fold (this step is optional so if you don't understand just skip it)


Step 7: Valley fold the bottom edge to the top, and mountain fold the far flap up at the same angle



Step 8: Valley fold the far right point to the far left


Step 9: Unfold


Step 10: Flip the model over so the top becomes the bottom


Step 11: Valley fold the model along the two points marked below (one is at the top of the crease made in step 8, and the other is just the edge of a flap)



Step 12: Unfold


Step 13: Outside reverse fold the flap up


Step 14: Now fold the far left point back so it is parallel to the body


Step 15: Unfold


Step 16: Inside reverse fold the flap up along the precreases made earlier


Step 17: Valley fold the point straight up


Step 18: Unfold


Step 19: Inside reverse fold the flap up


Step 20: Valley fold the point down (this will become the head, but leave the head slightly longer than normal)


Step 21: Unfold


Step 22: Outside reverse fold the flap down


Step 23: To form the beak (this is the underside view of the head) valley fold the tip, and then mountain fold it back

 It will look like this:

Flatten the head again, fold down the wings a little, and your swan is complete!



Comments

Post a Comment

Popular posts from this blog

Origami Basketball Hoop

By Dallin -
Image
The basketball hoop is a fun and interactive model. Once made, just crumple some paper into a ball and start shooting (you can also make a crumpled ball ). It can be made from either origami paper or printer paper. If you make it from origami paper, it won't be as tall, and won't stand up as easily, but it will still work. I would recommend making it from printer paper though. Also, it might fall over when being used, so just put a book or something behind it and it will stay up fine. Step 1: If you're using printer paper, orient it vertically. If you're using origami paper, make a  waterbomb base  and then skip to step 9. Step 2: Valley fold the top left corner over (the top edge should align with the right side) Step 3: Unfold Step 4: Valley fold the top right corner over to the left edge Step 5: Unfold and turn the paper over Step 6: After you've turned the paper over, fold the top edge down so the creases lie on t
Read more

Origami Dragon (harder)

By Dallin -
Image
The dragon is my favorite origami model but it is definitely not a beginner model. To fold it, you need to be able to petal, squash, sink, valley, and reverse fold. If you can't do all of  these folds, refer to the  folds  post. Step 1: Fold a  bird base  and have the separate points at the bottom Step 2: Valley fold the top point down Step 3: Mountain fold the top point down around the back Step 4: Valley fold the top point to the middle crease line, crease, and unfold Step 5: Now open the paper and sink fold the tip down. You will see a small square in the middle... ... and pinch the edges a little to define them... ...now press the center point down to 'sink' it It should look like this: Step 6: Valley fold the top layer on the right to the left Step 7: Valley fold the bottom point up Step 8: Valley fold point A to point B (refer to pic above) Step 9: Repeat steps
Read more

Oragami Inflatable Frog

By Dallin -
Image
The inflatable frog is a traditional Japanese origami model. It is a rather common model, but it's only one of many origami frogs out there. It is a rather advanced model, requiring squash and petal folds to make the base, and reverse folds to form the frog. It inflates, but is folded from a frog base rather than a waterbomb base. Step 1: Fold a  frog base Step 2: Valley fold the bottom right and left edges to the center Step 3: Repeat step 2 on the other three parts of the frog base  Step 4: Valley fold the top layer of the bottom two points up Step 5: Crease and unfold Step 6: Inside reverse fold the flaps up Step 7: Valley fold the two bottom points remaining out to their respective sides Step 8: Crease and unfold Step 9: Inside reverse fold the flaps Step 10: Now make reverse folds to form the arms and legs (use the picture below to know where to make your folds) Step 11: Blow into the litt
Read more